云南11选5

山东晟亚石材云南11选5欢迎您的光临!

全国咨询电话
18946249118 15214444313
联系我们 CONTACT US
山东晟亚石材云南11选5
联系人:刘经理

电话:18946249118 / 15214444313


地址:济宁市汶上县白石镇鑫亚石材厂
新闻资讯
当前位置:云南11选5> 云南11选5>新闻资讯>表面渗透加固的方式加固锈石!
表面渗透加固的方式加固锈石!
来源:http://www.bizzyball.com 日期:2019-07-31 发布人:admin
  可以说山东锈石使用较多,山东锈石有的比较硬,但也有一些脆性的石材,这时,我们需要装饰一些脆性的山东锈石,用一些表面渗透加固的方式来加固山东锈石。
  It can be said that Shandong rust stone is used more, Shandong rust stone is hard, but there are some brittle stones, at this time, we need to decorate some brittle Shandong rust stone, with some surface infiltration reinforcement to strengthen Shandong rust.
  “背网”加固是指非常高强度的纤维防护网
  "Back-net" reinforcement refers to a very high-strength fibre-reinforced protective net.
  孔网尺寸一般是5×5mm?用环氧树脂粘在木板背面的雪被烘干以加强木板的强度。整个光纤保护网的线圈宽度为1。2 - 1。8m分为不同规格,重量一般在900g/m2左右。
  The mesh size is usually 5 x5mm? The snow on the back of the board is dried with epoxy resin to enhance the strength of the board. The coil width of the whole optical fiber protection network is 1. 2 - 1. 8m is divided into different specifications, the weight is generally about 900g/m2.
  根据板材的实际需要,背网加固技术可用于大理石、花岗岩、石灰华、玛瑙等大型板材的加固。
  According to the actual needs of sheet metal, the reinforcement technology of back mesh can be used to reinforce large-scale sheets such as marble, granite, limestone, agate and so on.
  普通环氧树脂可以用来加固板的背网。可采用低、中、高粘度系列环氧树脂对板材进行加固。通常当补强板系列是最使用低粘度的环氧树脂,它们是在25℃凝固时间大约是30 - 50分钟,如果调整固化剂的比例加入25℃下的一些低粘度环氧树脂固化时间可以缩短到30 - 40分钟,甚至其他低粘度环氧树脂固化时间可以缩短到8 - 12分钟。一般来说,环氧树脂在室温下完全固化需要24小时。如果在干燥炉中加热,完全固化的时间可以明显缩短。
  Ordinary epoxy resin can be used to reinforce the back mesh of the board. Low, medium and high viscosity epoxy resin series can be used to reinforce the plate. Usually when the reinforcing plate series is the epoxy resin with the lowest viscosity, the solidification time is about 30 - 50 minutes at 25 C. If the ratio of curing agent is adjusted and some low viscosity epoxy resin at 25 C is added, the solidification time can be shortened to 30 - 40 minutes, and even the solidification time of other low viscosity epoxy resin can be shortened to 8 - 12 minutes. Clock. Generally speaking, it takes 24 hours for epoxy resin to be completely cured at room temperature. If heated in a drying furnace, the time of complete solidification can be significantly shortened.
山东锈石厂
  凝固时间是背网补强板的一个重要工艺参数,它取决于背网补强板的数量和输出,背网技术的运行方式,以及是否选择烘干炉,或者烘干炉的烘干能力等因素。生产线上待加强板数大、产量要求高时,可采用机械机械/化学背网加固方式,可选择自然室温全固化方式或平板固化加热炉烘干。如果产量要求很高,甚至可以选择立式干燥炉,此时应采用低粘度、固化时间短的环氧树脂比。
  Solidification time is an important technological parameter of backnet reinforcement plate. It depends on the number and output of backnet reinforcement plate, the operation mode of backnet technology, and whether to choose drying oven or drying capacity of drying oven. When the number of reinforcing plates on the production line is large and the output requirement is high, mechanical/chemical backnet reinforcing method can be adopted, and natural room temperature full curing method or flat-plate curing heating furnace can be selected for drying. If the output requirement is very high, the vertical drying furnace can even be chosen. At this time, the epoxy resin ratio with low viscosity and short curing time should be adopted.
  部分配筋量小、产量低的生产线,可采用手工背网作业方式,选择常温自然全固化方式,低粘度环氧树脂比,设置时间相对较慢,以减少生产线设备投资。
  For some production lines with small reinforcement and low output, manual back-net operation mode can be adopted, natural full curing mode at room temperature can be selected, low viscosity epoxy resin ratio can be set relatively slowly, so as to reduce the investment of production line equipment.
相关推荐
云南11选5 大河彩票APP 云南11选5走势图 云南11选5玩法规则 云南11选5走势图 云南11选5 云南11选5 云南11选5大赢家棋牌官网APP下载 云南11选5走势图 云南11选5开奖结果